HVM ASME, PED & CRN Threaded Filter Housings



Aluminum Filter Housings

Housing Features:

  • Carefully made from seawater-resistant aluminum, HVM filter housings are also anodized for better corrosion protection.
  • Filter ports match typical dryer and compressor pipe sizes.
  • HVM can also assemble filter combinations with/without water separators and with optional connection kits.
  • Maximum operating pressures available: 232 PSIG (Standard) or 725 PSIG (up to 2 inches)
  • Available with F, S and A Series filter elements.

Threaded Coalescing/Particulate Filters ½" - 3"
Model Pipe Size(in.) Flow Rate
(scfm)		 Dimensions Maximun
Operating
Pressure		 Weight(lbs) Aluminum Filter Housings
A B
HVM ACT-0.5-# 1/2" 70 2.95 10.43 232 2.65
HVM ACT.75-# 3/4" 105 3.94 11.02 232 3.75
HVM ACT-1.0-# 1" 170 3.94 15.16 232 4.85
HVM ACT-1.5-# 1 1/2" 290 5.75 16.46 232 9.92
HVM ACT-2.0-# 2" 690 5.75 26.89 232 15.65
HVM ACT-2.5-# 2 1/2" 1,100 10.24 30.51 232 49.82
HVM ACT-3-# 3" 1,675 10.24 41.14 232 65.92
Substitute the corresponding element type where appropriate:
# - F Series Microfilter Element
# - S Series Microfilter Element
# - A Series Activated Carbon

Carbon Steel & Stainless Steel Filter Housings

Housing Features:

  • Victaulic Coupling with double 'O' ring and bayonet for positively locating the element.
  • The 'O' ring eliminates possibility of particle or liquid bypass therefore insuring filtration integrity.
  • Stainless Steel construction, High-quality 304 and optional 316L, means no fouling or corrosion and long service life.
  • Plenum chamber design improves drainage from the filter housing when used to coalesce liquids.
  • Vents tapped 1/4" FNPT.
  • Available with F, S and A Series filter elements.
  • EPDM housing seal. Other elastomers available.
  • Also Available as connection type: BSP, NPT, and Socket Weld.

Threaded Coalescing/Particulate Filters ½" - 3"
Model Capacity (scfm) at 100 PSI G Flow Rate
(scfm)		 Dimensions Maximun Working Pressure (PSIG) Stainless Steel Filter Housings
A B C
HVM-FVT-0.5-XX-# 88 1/2" 11.8 4.3 3.9 232
HVM-FVT-0.75-XX-# 118 3/4" 13.2 4.3 4.5 232
HVM-FVT-1.0-XX-# 171 1" 15.2 5.3 4.6 232
HVM-FVT-1.5-XX-# 294 1 1/2" 15.2 5.3 4.6 232
HVM-FVT-2.0-XX-# 459 2 21.7 6.7 5.1 232
HVM-FVT-2.0H-XX-# 677 2 34 6.7 5.1 232
HVM-FVT-2.5-XX-# 853 2 1/2" 34 7.9 5.1 232
HVM-FVT-3.0-XX-# 1,148 3" 45 7.9 5.1 232
Maximum Operating Pressures Available - 232 PSIG (Standard) - Custom designs up to 5,000 PSIG
Substitute the corresponding material type and element type where appropriate:
XX - CS for Carbon Steel
XX - SS for Stainless Steel
# - F Series Microfilter Element
# - S Series Microfilter Element
# - A Series Activated Carbon
Pressure Conversion Factors
Pressure (PSIG) 5 10 14 28 43 57 71 86 100 114 128 148 157 171 186 200 217 232
Correction Factor 0.08 0.18 0.25 0.38 0.50 0.63 0.75 0.88 1 1.13 1.25 1.38 1.5 1.63 1.75 1.88 2 2.13

For maximum flow rate, multiply model flow rate show in the table by correction factor corresponding to the working pressure.